Nov 19, 2026
For compact devices that require a thin heating structure, controlled heat distribution, and integration into limited installation spaces, both JAYE and Heatron offer thick film heating technologies.
The appropriate design depends on the substrate material, heater geometry, operating temperature, watt density, electrical insulation, and connection requirements.
JAYE focuses on customized stainless steel thick film heating products, including thick film heater plates and instant hot water thick film heaters.
Heatron publishes a broader thick film portfolio covering stainless steel, aluminum, alumina, and aluminum nitride substrates. These products serve overlapping but not identical design requirements.
Therefore, a meaningful comparison should be based on the actual heater structure and operating conditions rather than brand names alone.

The figures above refer to published product information, not guaranteed performance in every assembled device.
Actual oper
ating limits depend on the selected model and application conditions.
A thick film heater is generally manufactured by depositing or printing functional materials onto a substrate.
The printed circuit forms the resistive heating path, while dielectric and protective layers provide electrical insulation and surface protection where required.
For metal-substrate heaters, the insulation layer separates the energized heating circuit from the conductive metal base.
The substrate then transfers the generated heat to the target component or medium.
The typical construction includes:
Heatron describes these construction layers in its technical explanation of thick film heater design.
JAYE's published stainless steel heater plate information also describes a printed heating circuit with multiple insulation layers on a stainless steel surface.【1】【2】
JAYE's published thick film product range includes stainless steel heater plates and instant hot water thick film heaters. These products are relevant to equipment where the heating element needs to be integrated into a limited space or directly coupled to a metal heating surface.
JAYE's thick film heater plate uses a stainless steel substrate with a printed heating circuit and insulation layers.
The structure allows the heating circuit to be integrated into a relatively flat metal component rather than installed as a separate conventional tubular element.
According to JAYE's published product information, the heater plate uses a stainless steel substrate and multilayer microcrystalline glass insulation. The product page lists a ramp-up rate of 80–150°C/s and a heat density above 60 W/cm² for the described product configuration.
It also lists a rated voltage of 220 V and a heating power of 5500 W.
These figures belong to the published product specification and should not be treated as universal limits for every customized thick film heater. The actual design needs to be reviewed against the required dimensions, voltage, wattage, thermal contact, and operating environment.【2】
Relevant product: JAYE Stainless Steel Thick Film Heater Plate
For equipment that heats water within a compact assembly, JAYE also provides instant hot water thick film heaters.
The published product description identifies stainless steel or ceramic as the base material, with a thick film heating layer.
The listed power range is 500–3000 W, with voltage options including 110 V, 220 V, and 240 V AC, as well as customized voltage options.
The product page also lists customizable dimensions and a thickness range of 1.2–1.5 mm.
These specifications make the product relevant to compact water-heating equipment where installation space and direct heat transfer are important design considerations.
For water-heating applications, the heater structure must be assessed together with water flow, inlet temperature, outlet temperature, pressure, scaling conditions, and electrical safety requirements. A heater's rated power alone does not determine the final water temperature or heating performance.
Relevant product: JAYE Instant Hot Water Thick Film Heater
Stainless steel is used as a substrate in thick film heating because it provides a mechanically robust metal base and can transfer heat to the equipment structure.
The printed heating circuit and insulation system must be designed together with the substrate.
For compact devices, the stainless steel substrate can serve as both the structural base and the heat-transfer surface.
Its thickness, shape, mounting arrangement, and contact area influence the overall thermal response of the assembled equipment.
JAYE's thick film heater plate product information provides a reference for this construction.
For a customized design, the required substrate material, thickness, outline, mounting points, and electrical connection details should be confirmed before production.
Related product: JAYE Stainless Steel-Based Thick Film Heater

The following comparison uses information published on the manufacturers' websites.
It focuses on stainless steel thick film heaters where the product categories overlap.
| Comparison point | JAYE | Heatron |
|---|---|---|
| Published thick film product | Stainless steel heater plate; instant hot water thick film heater | Stainless steel heater plates; aluminum and ceramic thick film products |
| Substrate information | Stainless steel; stainless steel or ceramic base listed for instant hot water product | Stainless steel, aluminum, alumina, and aluminum nitride across its portfolio |
| Heating circuit | Printed thick film heating circuit | Printed resistive and conductive materials |
| Insulation structure | Multiple insulation layers described for the stainless steel heater plate | Dielectric and protective layers selected according to substrate and application |
| Published maximum temperature | No directly comparable maximum operating temperature confirmed for the JAYE heater plate page | Up to 650°C for the stainless steel thick film heater |
| Published watt density | Above 60 W/cm² listed for the JAYE heater plate product | 31 W/cm² maximum listed for the stainless steel thick film heater |
| Published ramp-up rate | 80–150°C/s listed for the JAYE heater plate product | 150°C/s listed for the stainless steel thick film heater |
| Customization | Customized voltage, power, dimensions, and substrate requirements are requested on JAYE product pages | Custom shapes, machining, sensor options, connection schemes, and watt-density designs are described |
| Compact device relevance | Flat heater plates and instant water-heating structures | Low-profile stainless steel heaters for compact, high-temperature applications |
Important comparison note: The published JAYE heater plate figures and Heatron stainless steel heater figures are manufacturer-listed specifications. They may refer to different product designs, test conditions, or measurement methods. The higher published watt-density figure alone does not establish that one heater performs better than the other. A direct comparison requires equivalent substrate dimensions, test conditions, insulation construction, and thermal loading.
Sources: JAYE product specifications and Heatron's stainless steel thick film heater page.【2】【3】
In compact equipment, the heating element is not selected by wattage alone. The substrate and physical structure determine how the heater can be installed and how heat moves into the target component.
Heatron publishes products using all four substrate categories.
JAYE's publicly listed thick film products discussed in this article focus on stainless steel and stainless steel or ceramic-based constructions.
These should not be assumed to have identical material options or performance envelopes.【3】【4】
A compact device may have limited room for the heating element, terminals, sensor, insulation, and mounting hardware.
Before selecting a thick film heater, engineers should check:
A heater that fits the available outline may still have poor thermal contact if the mounting surface is uneven or the contact pressure is insufficient.
Mechanical integration and heat-transfer design must therefore be evaluated together.
Watt density describes the electrical power applied per unit of active heating area.
A higher watt density can support greater heat output from a limited surface, but it also increases the importance of heat transfer, insulation, and temperature monitoring.
For compact devices, the heating pattern should match the heat demand of the target area.
If one section loses more heat than another, a uniformly distributed heating circuit may not produce a uniform operating temperature.
The required watt density should be assessed using the target temperature, heating time, thermal mass, heat loss, contact conditions, and duty cycle.
It should not be selected only by comparing catalogue maximum values.
JAYE's thick film products are relevant to several equipment categories where a compact heating structure is required.
| Application | Main heating requirement | Relevant JAYE product |
|---|---|---|
| Instant water dispensers | Rapid heat transfer to flowing water within a compact assembly | Instant hot water thick film heater |
| Food service equipment | Heating a metal surface or integrated heating plate | Stainless steel thick film heater plate |
| Laboratory equipment | Defined heating area and integration into equipment structures | Customized thick film heater plate |
| Semiconductor-related equipment | Controlled heat delivery and suitable substrate configuration | Thick film heater, subject to technical review |
| Home appliances | Space-efficient heating structure and customized electrical specifications | Stainless steel thick film heater |
These are potential application areas, not claims that one standard heater design fits every device. The final configuration depends on the equipment's thermal and mechanical requirements.
For OEM equipment manufacturers comparing JAYE and Heatron thick film heaters, the following technical information helps establish whether a proposed design is suitable.
1. Define the heating target
Identify whether the heater warms a metal plate, a component surface, flowing water, or another medium. The heat-transfer path determines the required substrate and installation structure.
2. Confirm electrical requirements
Specify rated voltage, power, AC or DC supply, frequency where applicable, and allowable power tolerance. These values determine the resistance and circuit design.
3. Confirm operating temperature
Provide the required working temperature, maximum temperature, heating cycle, and control method. The maximum temperature of a heater material or product category should not be confused with the normal operating temperature of the assembled equipment.
4. Review thermal contact and heat distribution
Provide the mating surface material, contact area, mounting method, and expected heat loss. These details affect the temperature distribution and the risk of localized overheating.
5. Confirm insulation and safety requirements
Specify dielectric strength, insulation resistance, leakage current, grounding method, and any applicable product or industry standards. These requirements should be confirmed against the actual equipment design.
6. Define sensor and connection arrangements
Identify whether an NTC, RTD, thermocouple, thermostat, or thermal fuse is required. Also confirm lead type, terminal position, connector, and available wiring space.
7. Validate the prototype under actual conditions
A prototype should be evaluated in the intended assembly. Relevant checks may include temperature distribution, ramp-up time, insulation performance, thermal cycling, and operation under the expected load.
JAYE is a potential manufacturing option for OEM customers who need a customized thick film heating element based on a defined drawing, sample, or set of technical specifications.
The published product range provides reference structures for stainless steel thick film heater plates and instant hot water thick film heaters. For projects involving compact devices, JAYE can review the requested dimensions, substrate, voltage, wattage, and connection arrangement to assess manufacturing feasibility.
A direct replacement for a Heatron heater should not be assumed from product category or external dimensions alone. The original heater's resistance pattern, insulation system, substrate properties, thermal performance, and safety requirements need to be reviewed before interchangeability can be evaluated.
For projects with an existing Heatron heater, an original sample, technical drawing, or datasheet is useful for the initial review.
Not automatically. Replacement feasibility depends on the substrate material, dimensions, heating circuit, voltage, wattage, insulation requirements, temperature range, and mechanical interface. JAYE can review an original drawing or sample to assess whether a corresponding design is manufacturable.
The maximum operating temperature depends on the specific heater construction and application. JAYE's published thick film heater plate page lists a ramp-up rate and other product parameters, but does not establish a directly comparable maximum operating temperature for every JAYE thick film heater. The required operating temperature should be confirmed for the intended model.
A stainless steel thick film heater uses a metal substrate that can provide structural support and a heat-transfer surface. A ceramic thick film heater uses an electrically insulating ceramic substrate, with thermal conductivity and mechanical properties depending on the ceramic material. The choice depends on operating temperature, insulation, thermal transfer, and mechanical requirements.
No. Higher watt density means more electrical power is applied per unit area, but it does not automatically produce better system performance. The substrate, thermal contact, heat loss, temperature control, and allowable surface temperature must all be considered.
The most useful starting information includes:
【1】Heatron – The Basic Components and Structure of a Thick Film Heater:https://www.heatron.com/news-and-events/news/basic-components-and-structure-of-a-thick-film-heater
【2】JAYE – Thick Film Heater Plate
【3】Heatron – Thick Film Stainless Steel Heater Plates:https://www.heatron.com/products--services/thick-film-heating-elements-and-circuits/thick-film-stainless
【4】Heatron – Thick Film Heating: Introduction:https://www.heatron.com/news-and-events/news/thick-film-heating-introduction
【5】JAYE – Instant Hot Water Thick Film Heater
【6】JAYE – Comparison of Thick Film Heating and Thin Film Heating

JAYE provides stainless steel thick film heater plates and instant hot water thick film heaters, with customized specifications subject to technical review.
Previous: No Information
Next: Backer Element Substitute for Home Appliances: JAYE Quality Check