Sep 18, 2026
If you manufacture air curtains, you already know the heating element is where most field failures originate. An air curtain sits above a doorway, exposed to humidity, temperature swings, and the constant cycling that comes with door traffic. When the heating element fails, the air curtain becomes an expensive fan-it moves air, but it doesn't stop cold drafts, doesn't protect the indoor climate, and doesn't deliver the energy savings it promised.
That's why sourcing the right finned heating tube matters more than most procurement teams realize. We've been making finned tubular heaters for air curtain OEMs at Jaye Heater for over a decade, and we've seen what happens when manufacturers cut corners on this component-warranty claims, field failures, and customers who start questioning the entire specification.
Here's what we've learned about sourcing finned heating tubes that actually perform in air curtain applications.
Air curtain heating elements operate in a forced-convection environment. The fan pushes air across the heating element at velocities typically in the 6 to 12 m/s range at the discharge. Air is a poor heat transfer medium-its thermal conductivity is a fraction of water's or metal's. A bare tubular heater has to run at high sheath temperatures to push enough heat into the passing air, which means thermal stress, faster oxidation, and shorter element life.
Finned tubular heaters solve this by extending the heat transfer surface. A helical fin-typically 4 to 5 fins per inch-is wound onto the tubular sheath and permanently brazed in place. The finned surface area can be 10 to 15 times that of a bare tube of the same length. In practical terms, a finned element can dissipate 2.5 times more heat than a bare tube of the same dimensions, and the allowable surface power load increases 3 to 4 times . For an air curtain, that means you can achieve the required kW output in a more compact housing, or pack more heating capacity into the same footprint.
Not all finned tubular heater suppliers are created equal. Here's what we'd tell any air curtain OEM to check.
This is where many suppliers cut corners. Fins should be continuously wound and furnace-brazed to the sheath. Press-fit fins-where the fins are just crimped onto the tube-will loosen over time under thermal cycling. Once fins start rattling loose, heat transfer drops, the element overheats, and failure follows .
If the fin isn't fully brazed to the sheath, there's thermal contact resistance at the interface. Experimental studies on finned tubes put contact conductance values in the range of 3,500 to 11,000 W/m²K, depending on air velocity and fin attachment quality. A poorly bonded fin creates a thermal bottleneck that defeats the purpose of adding surface area. Furnace-brazed fins-where the fin is metallurgically fused to the sheath-eliminate that interface resistance. The fin and sheath behave as a single piece of metal.
We mechanically lock and braze every fin at Jaye Heater. It takes more time and costs more to produce, but it's the only way to ensure fins stay put through thousands of thermal cycles .
Stainless steel 304 is the baseline for most air curtain applications. But if your air curtain will be installed in coastal areas, high-humidity environments, or locations with airborne chlorides and chemical contaminants, SS316L or Incoloy 800 provide better corrosion resistance. For extreme temperatures, SS321 offers better high-temperature stability .
The fin material should match the sheath to avoid galvanic issues at the brazed interface. Most air curtain OEMs use stainless steel fins as standard. If you're specifying SS316 for the sheath, make sure the fins match.
Air curtain applications vary widely. Small doorways may need 3kW elements; large industrial openings can require 10kW or more. Voltage compatibility matters too-230V is common, but many air curtains run at 208V, 400V, or 480V. Your supplier should offer a broad range and be willing to customize. If they only stock a few standard sizes, they're not equipped to support your product line as it evolves .
If you're exporting air curtains to North America or Europe, UL 499 and CE certifications are non-negotiable. UL 499 is the U.S. safety standard for commercial and industrial electric heating appliances, and it explicitly covers air curtains . The standard includes temperature rise tests under normal and abnormal (blocked airflow) conditions, dielectric voltage-withstand tests, and leakage current evaluations . For Europe, air curtains typically fall under EN 60335-2-30 or EN 60335-2-80 standards, or carry the CE mark .
A supplier who doesn't hold these certifications will create headaches for your compliance team down the road. Ask for the certification documentation upfront-not after you've placed the order.
This is the invisible differentiator. A good supplier tests every batch-raw material inspection, dimensional checks, dielectric strength testing, and thermal performance validation. Look for suppliers equipped with fin bonding lines, tube expansion tools, and hydrostatic test rigs .
We've seen competitors skip these steps to save cost. The result is heater-to-heater variation that makes air curtain calibration impossible. Your air curtain is only as consistent as its heating elements.
When you're evaluating potential suppliers, here's a checklist we'd recommend:
How are the fins attached? If the answer isn't "furnace-brazed," you're taking a risk.
What sheath materials do you offer? SS304, SS316L, SS321, Incoloy 800-a supplier who only offers one grade isn't equipped to match your application.
What certifications do you hold? UL 499, CE, CQC, RoHS. Ask for the certificates, not just a verbal confirmation.
Can you provide samples for airflow testing? A supplier confident in their product will send samples before asking for a production order.
What's your lead time for custom configurations? Air curtain designs evolve. A supplier who can't adapt to new dimensions or wattages will hold your product development back.
We're a manufacturer, not a trading company. That means we control the entire production process-from raw material sourcing to final testing. We've been at this for over ten years, and we specialize in custom finned tubular heaters for air curtain applications.
Our finned tubular heaters offer:
2.5x greater heat dissipation than standard tubular heaters
2–3x higher surface load capacity
Multiple sheath options – SS304, SS316L, SS321, Incoloy 800
Furnace-brazed fins that stay put through thermal cycling
UL certifications
Custom shapes and sizes – straight, U, W, or any configuration your design requires
We work with air curtain OEMs to develop heating elements that match their exact specifications. If you send us your duct dimensions, airflow rate, target temperature rise, and voltage, our engineers will calculate the optimal finned heater configuration.
Ready to source finned heating tubes for your air curtain line? Send us your specifications-wattage, voltage, dimensions, airflow rate, and annual volume. We'll recommend a configuration, provide samples for testing, and quote production pricing. We've helped air curtain manufacturers across commercial, industrial, and cold storage sectors get heating elements they can rely on.
Contact us today for a quote.
Previous: Where to Source PTC Cartridge Heater for Condensate Pans?
Next: How do you Choose Straight, U-Shape, and W-Shape Finned Heaters for Air Curtains?
