Nov 13, 2026
JAYE and BriskHeat both offer silicone rubber-based flexible heating products for surface heating applications, but their published product ranges and configuration approaches are different.
BriskHeat provides defined silicone rubber heating blanket series, including SRL and SRP, with published power densities for metal and plastic surfaces.
JAYE focuses on customized silicone rubber heating elements, with options for dimensions, voltage, wattage and heating element construction.
For equipment manufacturers comparing a BriskHeat flexible heater with a JAYE alternative, the key considerations include the heated surface material, required power per unit area, operating temperature, installation dimensions, electrical connections and temperature control requirements.
The two brands should be evaluated against the actual application rather than assumed to be direct replacements.
| Comparison Item | BriskHeat | JAYE |
|---|---|---|
| Product Examples | SRL/SRP Silicone Rubber Heating Blankets | Silicone Flexible Blanket Heating Element |
| Product Approach | Defined product series with selectable configurations | Custom heating element manufacturing |
| Heating Element Construction | Heating element laminated between fiberglass-reinforced silicone rubber layers | Resistance wire or etched foil construction, depending on design |
| Published Power Density / Output | SRL: 0.39 W/cm²; SRP: 0.19 W/cm² | Up to 5 kW/m² (0.5 W/cm²) on the flexible blanket product page |
| Voltage | 120–600 VAC for SRL/SRP | AC or DC voltage on request |
| Temperature Information | Exposure temperature: -51°C to 232°C | Maximum surface temperature: 300°C; minimum exposure temperature: -60°C |
| Published Thickness | 4.8 mm nominal | 4.5 mm |
| Maximum Published Width | Selectable product dimensions; series-specific | 48 inches (approximately 1219 mm) |
| Temperature Control | External temperature controller required for SRL/SRP | Control and sensor requirements can be evaluated according to the project |
| Customization | Width, length, surface type and optional adhesive backing | Size, shape, voltage and output according to project requirements |
Important: The figures above are published product-range specifications, not results from a controlled side-by-side test.
BriskHeat's exposure temperature and JAYE's maximum surface temperature are different rating descriptions.
Actual operating limits must be checked against the specific heater construction and application.
BriskHeat's SRL and SRP silicone rubber heating blankets are designed for surface heating on equipment such as tanks, vessels, hoppers, silos and conveyors.
One notable feature of this product family is its distinction between heating metal and plastic surfaces:
SRL Series: Published power density of 2.50 W/in² (0.39 W/cm²) for metal surfaces.
SRP Series: Published power density of 1.25 W/in² (0.19 W/cm²) for plastic surfaces.
The SRL/SRP construction uses a heating element laminated between two layers of fiberglass-reinforced silicone rubber. An optional pressure-sensitive adhesive backing is available for mounting onto suitable smooth surfaces.
The product page specifies a nominal thickness of 4.8 mm, an exposure temperature range of -51°C to 232°C, and a minimum bend-radius specification of 51–76 mm.
An external temperature controller is required for the SRL/SRP product.
This is an important point for equipment manufacturers: the heater blanket and its control arrangement need to be considered as part of the complete installation.
BriskHeat also publishes an IP56 rating for this product family.
Certification and temperature limitations should be checked against the exact model and approval requirements.
JAYE manufactures silicone rubber heating elements for OEM equipment and customized heating projects. Instead of limiting the discussion to one standard blanket configuration, the design can be evaluated according to the required dimensions, electrical rating and installation conditions.
The published Silicone Flexible Blanket Heating Element specifications include:
The heating element can use resistance wire or etched foil technology, depending on the design.
These options are relevant when an OEM project requires a particular outline, heated area, lead-wire arrangement or electrical specification. The final construction and operating limits need to be confirmed through drawing and engineering review.
JAYE's published specifications should not be interpreted as a guarantee that every combination of maximum width, output, voltage and temperature can be used simultaneously. The feasible combination depends on the actual heater dimensions, substrate, thermal conditions and construction.

A flexible heater should be evaluated as part of the equipment's thermal and mechanical design. Comparing only the maximum temperature or watt density can lead to an unsuitable selection.
The material receiving heat affects the allowable power density and the temperature distribution across the contact area.
For example, BriskHeat specifies different power densities for its SRL and SRP products: 0.39 W/cm² for metal surfaces and 0.19 W/cm² for plastic surfaces.
This distinction matters because metal and plastic components have different thermal conductivity, heat capacity and temperature limitations. A power density suitable for a metal vessel should not automatically be transferred to a plastic enclosure.
For a customized JAYE heater, the substrate material and contact conditions should be included in the technical review. The required wattage may need to be adjusted according to the actual heat transfer conditions.
Power density describes the electrical heating output relative to the active heating area. It is usually expressed in W/cm² or W/in².
The relationship is:
Total heater power = Power density × Active heating area
For example, a heater with an active area of 500 cm² and a power density of 0.2 W/cm² has a nominal output of 100 W.
This calculation provides an initial electrical design reference. It does not independently determine the required heater power because heat loss, insulation, ambient temperature, target temperature and warm-up time must also be considered.
When comparing JAYE and BriskHeat, the published SRL and SRP power densities can be compared numerically with JAYE's published maximum output of 0.5 W/cm². However, the figures do not establish equivalent heating performance because the product series, surface conditions and test methods may differ.
Maximum exposure temperature, maximum heater surface temperature and controlled process temperature describe different operating conditions.
BriskHeat publishes an exposure temperature range of -51°C to 232°C for SRL/SRP. Its product page also notes that the cRUus approval applies up to 181°C.
JAYE's flexible blanket product page lists a maximum surface temperature of 300°C. This should not be treated as a universal continuous operating temperature for every custom design.
For an actual project, engineers should define:
The control system should be selected according to the equipment's operating and safety requirements. A heating element alone does not establish the accuracy of the complete temperature control system.
The available mounting area determines the heater's outline, active heating zone and lead exit position.
For a flexible blanket installed on a curved vessel, the heater must fit the surface without excessive mechanical stress. The bend radius, contact pressure and surface geometry should be reviewed before installation.
BriskHeat publishes a bend-radius range of 51–76 mm for SRL/SRP. JAYE's custom design should be evaluated against the actual shape and installation drawing rather than assumed to have the same bending characteristics.
For irregular surfaces, equipment manufacturers should provide the full outline drawing and identify the area that needs to be heated.
Voltage, resistance, wattage and lead-wire specifications must be checked together.
For example, changing the supply voltage without redesigning the heater's electrical resistance can significantly change its output. Lead-wire insulation, terminal construction and grounding arrangements also need to match the operating environment.
BriskHeat SRL/SRP requires an external temperature controller. For a JAYE custom project, the required sensor, thermostat, thermal fuse or external controller arrangement should be specified separately and reviewed according to the equipment design.
Flexible silicone heaters are used when heat needs to be transferred across a surface rather than concentrated at a single point. The following examples illustrate how application conditions affect the selection.
Tank heating projects may involve maintaining the temperature of water, oil, chemicals or other process materials.
The main engineering considerations include:
BriskHeat SRL/SRP is published for tanks, vessels, vats and similar equipment.
A JAYE custom blanket may also be evaluated where the equipment requires a specific size, shape or electrical configuration.
For chemical or process liquids, compatibility of the tank material and the complete heating arrangement must be reviewed.
The silicone heater should not be assumed to be suitable for direct immersion.
In outdoor equipment, a flexible heater may be used to reduce the risk of freezing or maintain a minimum temperature.
The required heater output depends on ambient temperature, wind exposure, insulation, equipment geometry and the minimum temperature to be maintained.
A heater's maximum power density alone cannot establish whether it can provide sufficient freeze protection.
A heat-loss calculation and temperature-control plan are necessary for the actual installation.
Hoppers and storage vessels may require surface heating to help maintain material temperature or manage viscosity.
The heated area should be selected according to the material flow path and the locations where heat is required.
Uneven heating may create local temperature differences, so heater placement and sensor position should be considered together.
BriskHeat lists hoppers and silos among the SRL/SRP application examples. JAYE can review custom blanket dimensions and heating zones based on the equipment drawing.
For OEM equipment, the heater may need to fit a dedicated installation area with defined mounting dimensions, cable routing and electrical interfaces.
A custom silicone heater can be evaluated when standard blanket dimensions do not match the equipment layout. However, the heater design still needs to meet the thermal, electrical and mechanical requirements of the application.

JAYE SILICONE DURM HEATER
If an equipment manufacturer is considering a JAYE flexible heater as an alternative to a BriskHeat product, the first step is to identify the exact BriskHeat series and configuration.
A comparison based only on the term "silicone rubber heater" is insufficient.
SRL, SRP and other BriskHeat product families may have different electrical, mechanical and application specifications.
The following information helps establish whether a JAYE configuration can be evaluated:
A drawing or photograph of the existing heater is useful for an initial review.
The original product's technical datasheet should also be provided whenever possible.
JAYE can assess whether the required dimensions, output, materials and connections are feasible for a custom manufacturing project.
A proposed alternative should be verified through drawing approval and application testing before it is treated as a qualified replacement.

Not automatically. The two products need to be compared by dimensions, power density, voltage, temperature limits, mounting arrangement and control requirements. A custom JAYE design may be evaluated against the original specification, but compatibility should be confirmed through technical review and testing.
According to BriskHeat's published specifications, SRL is rated at 2.50 W/in² (0.39 W/cm²) for metal surfaces, while SRP is rated at 1.25 W/in² (0.19 W/cm²) for plastic surfaces. The lower SRP power density is intended for applications involving plastic surfaces. The substrate and operating temperature limitations must still be checked.
A preliminary calculation uses:
Wattage = Active heating area × Power density
For example, an active area of 500 cm² at 0.2 W/cm² gives a nominal heater output of 100 W.
This is only an initial electrical calculation. The final wattage should also account for heat loss, insulation, ambient temperature, target temperature and warm-up time.
It depends on the product configuration. BriskHeat specifies that its SRL/SRP heating blankets require a temperature controller. For other custom heaters, the sensor and controller arrangement should be defined according to the equipment's control and safety requirements.
Provide the heater dimensions, active heating area, voltage, wattage or resistance, target temperature, heated surface material, mounting method and lead-wire requirements. If replacing an existing BriskHeat heater, include its model number, datasheet and installation photos.
BriskHeat. Heavy-Duty Silicone Rubber Heating Blankets (SRL/SRP). Official product specifications, construction, applications and approvals.
BriskHeat. Silicone Rubber Heating Blankets with Control (SRL/SRP). Product series specifications and temperature-control information.
JAYE Heater Technology. Silicone Flexible Blanket Heating Element. Published dimensions, output, voltage and temperature specifications.
JAYE Heater Technology. Silicone Rubber Heater. Heating element construction and customization information.
JAYE Heater Technology. Silicone Rubber Heat Pad. Published silicone rubber pad specifications and construction details.

JAYE can review your existing flexible heater specifications, equipment drawings and application requirements to evaluate a customized silicone rubber heating element.
Previous: JAYE PI Flexible Heater vs Minco PI Heater: Tolerance Comparison
Next: JAYE Cartridge Heater vs Durex Cartridge Heater: Mold & Tool